hulika

Author Topic: peeves' DIY Electronic Drumkit  (Read 55286 times)

Offline peeves24

  • Philmusicus Addictus
  • *****
Re: peeves' DIY Electronic Drumkit
« Reply #125 on: July 06, 2017, 11:37:58 PM »
clarify ko lang yung raper circuit hehehe

yung old trigger inputs kasi ng module dati pag dual zone is always piezo/switch. ngayon madalas piezo yung kailangan mo kung mag exexpand ka ng pads at sayang yung extra switch input kasi hindi mo makakabitan ng piezo yun. kaya merong raper circuit, para magamit mo yung switch input din sa piezo.

yung trigger io kasi pwede mo iconfigure sa menu nya yung input types: pwedeng piezo/piezo, piezo/switch so di mo na kailangan nung raper circuit kasi nga pwede naman gawing piezo/piezo na yung trigger input with sa trigger io.

yung raper circuit, dalawa purpose nya:

1. yung old piezo/switch input pwede mo saksakan ng piezo/piezo so pwedeng dual zone cymbal e.g. ride and bell o kaya dual zone pad isa center at isa sa rim.

2. syempre pwede rin maging 2 invidual single zone pads yung ikabit sa piezo/switch input

balikan mo manual ng trigger io medyo hindi ko na kabisado yung mga input types e.

Offline jake z

  • Forum Fanatic
  • ****
Re: peeves' DIY Electronic Drumkit
« Reply #126 on: July 06, 2017, 11:42:48 PM »
I have a question sir Peeves. I have an alesis dm7x and yung toms nya is dual zone. right now, yung middle portion is for the toms but the edges are for my additional cymbals.

I am planning on diy'ng para may seperate cymbals talaga. Not sure where to start but I think from the cable na nag coconnect sa isang tom, need ko ng splitter para meron pa akong input sa tom and for the diy cymbal. tama ba?

thanks!

Offline peeves24

  • Philmusicus Addictus
  • *****
Re: peeves' DIY Electronic Drumkit
« Reply #127 on: July 07, 2017, 01:46:21 AM »
yes tama. Y splitter lang kailangan mo

Offline jake z

  • Forum Fanatic
  • ****
Re: peeves' DIY Electronic Drumkit
« Reply #128 on: July 07, 2017, 02:17:12 AM »
yes tama. Y splitter lang kailangan mo

thanks for the response sir peeves.

sorry ha, confused pa rin ako. noob regarding electronics.

pag dual zone ba stereo yung cable? if thats so, kung iisplit ko sya, dapat may specific wiring yung pagdating sa stereo cable from the module itself. tama ba?

thank you again!

Offline peeves24

  • Philmusicus Addictus
  • *****
Re: peeves' DIY Electronic Drumkit
« Reply #129 on: July 07, 2017, 03:51:26 AM »
oo stereo cable yun.  wala naman specific wiring. imagine mo lang dalawang mono signal sya tapos configure mo na lang sa module kung ano tunog na lalabas per pad


Offline jake z

  • Forum Fanatic
  • ****
Re: peeves' DIY Electronic Drumkit
« Reply #130 on: July 07, 2017, 04:01:12 AM »
oo stereo cable yun.  wala naman specific wiring. imagine mo lang dalawang mono signal sya tapos configure mo na lang sa module kung ano tunog na lalabas per pad

thanks sir Peeves. Kaka print ko lang ng instructibles from this thread, hopefully maging ok ang outcome ng diy.

Offline harmonicconverger

  • Netizen Level
  • **
Re: peeves' DIY Electronic Drumkit
« Reply #131 on: July 07, 2017, 01:54:49 PM »
clarify ko lang yung raper circuit hehehe

yung old trigger inputs kasi ng module dati pag dual zone is always piezo/switch. ngayon madalas piezo yung kailangan mo kung mag exexpand ka ng pads at sayang yung extra switch input kasi hindi mo makakabitan ng piezo yun. kaya merong raper circuit, para magamit mo yung switch input din sa piezo.

yung trigger io kasi pwede mo iconfigure sa menu nya yung input types: pwedeng piezo/piezo, piezo/switch so di mo na kailangan nung raper circuit kasi nga pwede naman gawing piezo/piezo na yung trigger input with sa trigger io.

yung raper circuit, dalawa purpose nya:

1. yung old piezo/switch input pwede mo saksakan ng piezo/piezo so pwedeng dual zone cymbal e.g. ride and bell o kaya dual zone pad isa center at isa sa rim.

2. syempre pwede rin maging 2 invidual single zone pads yung ikabit sa piezo/switch input

balikan mo manual ng trigger io medyo hindi ko na kabisado yung mga input types e.

Thank you so much sir. Clear na sya saken ngayon. Akala ko ko po kasi nun ang raper circuit is to avoid crosstalk for dual zone pads. Ngayon malinaw na po. Salamat po ng marami sir. Napakalaking tulong.