Amplifier for your subwoofers

[CodeOne]

  Crell CA-25   php 52,000

[tjlimjoco]

Crell CA-25   php 52,000

+ 1. Try nyo din yung Peavey PV3800. Nasa 41k discounted na. Natry na ng mga ibang kakilala ko malakas din daw at malinis. 

[stoney73]

The Peavey PV3800 will do.  Can power my old Fane Colossus 18" for a mid-size gig. 2 per side.




Fane Colossus

I'll be trying this amp on the P Audio C-18elf very very soon. Update ko kayo

[lowriderthug]

Okey ba itong amp na ito kung bridged natin?



Model    MR-2600               
Frquency Response    20Hz-20KHz               
8 ohm stereo            2X630W               
4 ohm stereo            2X1020W               
8 ohm Bridged            1500W               
Total Harmonic Distortion    <0.5%               
Damping Factor             (400Hz~1KHz)>400               
Input Impedance            10Kohm               
S/N Ratio                    >100dB               
Power Supply            AC-180V~240V, (50HZ~60HZ)               
Voltage Gain            39dB               
Dimensions                    88x483x485mm               
Packing Dimensions    540x530x190mm               
Weight                    23 kg


P23,600

im still looking for other amps, any suggestions? thanks

[CodeOne]

ACM-M21200 Professional Power Amplifier

SPECIFICATION:

Rated power bridge mode 8 Ohms    3600Watts @ 1 kHz at <0.5% T.H.D.
Rated power (2 X4 Ohms):    1800 Watts per channel @ 1 kHz at <0.5%
T.H.D. both channels driven
Rated power (2 X 8 Ohms):    1200 Watts per channel @ 1 kHz at <0.5%
T.H.D.both channels driven
Power bandwidth:    20 Hz - 20kHz; +0, -0.5 dB at rated 500 Watts 8 Ohm power
T.H.D.(2 X 4 Ohms):    <0.05%@900 Watts per channel from 20 HZ to 20 kHz
T.H.D.(2 X 8 Ohms):    <0.05%@600Watts per channel from 20 HZ to 20 kHz
Minimum load impedance:    2 Ohms
Maximum RMS voltage swing:    110Volts
Frequency response:    10 Hz - 50 kHz; +0, -3 dB at 1 Watt
Input CMRR:    >-65 dB @ 1 kHz
Rated power (1 X 4 Ohms):    1980 Watts @ 1 kHz at <0.5% T.H.D.
Rated power (1 X 8 Ohms):    1300 Watts @ 1 kHz at <0.5% T.H.D.
Phase response:    +20 to -25 from 20 Hz to 20 kHz
Input impedance:    20 k Ohms, balanced; 10k Ohms, unbalanced
Cooling:    Tow temperature dependant variable speed 120mm high output DC fans
Controls:    Two front panel attenuators, rear panel mode switch and gain select switch
Voltage gain:    0.775V, 32 dB or 26 dB
Crosstalk:    >-60 dB @ 1 kHz at rated power @ 8 Ohms
Hum and noise:    >-104 dB, "A" weighted referenced to rated power @ 8 Ohms
Slew rate:    >25V/us
Damping factor (8 Ohms):    >800:1 @ 20Hz - 1 kHz
Indicator LEDs:    2 Clip,2 signal presence, 2 active status, 2Protection
Protection:    Thermal, DC, turn-on bursts, incorrect loads
Connectors:    XLR, Speakon and Binding Post speaker output,
240/230 Volt 20 amp IEC mains
Construction:    16 ga. Steel
Dimensions:    132mm x 483 mm x 498 mm
Net weight:    36kg
Gross weight:    39kg

[/b][/b][/b]

[JVP]

ACM-M21200 Professional Power Amplifier

SPECIFICATION:

Rated power bridge mode 8 Ohms    3600Watts @ 1 kHz at <0.5% T.H.D.
Rated power (2 X4 Ohms):    1800 Watts per channel @ 1 kHz at <0.5%
T.H.D. both channels driven
Rated power (2 X 8 Ohms):    1200 Watts per channel @ 1 kHz at <0.5%
T.H.D.both channels driven
Power bandwidth:    20 Hz - 20kHz; +0, -0.5 dB at rated 500 Watts 8 Ohm power
T.H.D.(2 X 4 Ohms):    <0.05%@900 Watts per channel from 20 HZ to 20 kHz
T.H.D.(2 X 8 Ohms):    <0.05%@600Watts per channel from 20 HZ to 20 kHz
Minimum load impedance:    2 Ohms
Maximum RMS voltage swing:    110Volts
Frequency response:    10 Hz - 50 kHz; +0, -3 dB at 1 Watt
Input CMRR:    >-65 dB @ 1 kHz
Rated power (1 X 4 Ohms):    1980 Watts @ 1 kHz at <0.5% T.H.D.
Rated power (1 X 8 Ohms):    1300 Watts @ 1 kHz at <0.5% T.H.D.
Phase response:    +20 to -25 from 20 Hz to 20 kHz
Input impedance:    20 k Ohms, balanced; 10k Ohms, unbalanced
Cooling:    Tow temperature dependant variable speed 120mm high output DC fans
Controls:    Two front panel attenuators, rear panel mode switch and gain select switch
Voltage gain:    0.775V, 32 dB or 26 dB
Crosstalk:    >-60 dB @ 1 kHz at rated power @ 8 Ohms
Hum and noise:    >-104 dB, "A" weighted referenced to rated power @ 8 Ohms
Slew rate:    >25V/us
Damping factor (8 Ohms):    >800:1 @ 20Hz - 1 kHz
Indicator LEDs:    2 Clip,2 signal presence, 2 active status, 2Protection
Protection:    Thermal, DC, turn-on bursts, incorrect loads
Connectors:    XLR, Speakon and Binding Post speaker output,
240/230 Volt 20 amp IEC mains
Construction:    16 ga. Steel
Dimensions:    132mm x 483 mm x 498 mm
Net weight:    36kg
Gross weight:    39kg

[/b][/b][/b]

SIR MAGKANO TONG AMP NA ITO ACMAUDIO M21200

[CodeOne]

  around 32k yata sir price nito sa market.

[Jef2]

Okey ba itong amp na ito kung bridged natin?



Model    MR-2600               
Frquency Response    20Hz-20KHz               
8 ohm stereo            2X630W               
4 ohm stereo            2X1020W               
8 ohm Bridged            1500W               
Total Harmonic Distortion    <0.5%               
Damping Factor             (400Hz~1KHz)>400               
Input Impedance            10Kohm               
S/N Ratio                    >100dB               
Power Supply            AC-180V~240V, (50HZ~60HZ)               
Voltage Gain            39dB               
Dimensions                    88x483x485mm               
Packing Dimensions    540x530x190mm               
Weight                    23 kg


P23,600

im still looking for other amps, any suggestions? thanks

as much as possible, try avoiding the 'bridged mode'.  look for a power amp that has a really high power rating per channel so that you can maintain a normal L & R stereo set-up.

hope this helps.

[lowriderthug]

as much as possible, try avoiding the 'bridged mode'.  look for a power amp that has a really high power rating per channel so that you can maintain a normal L & R stereo set-up.

hope this helps.

Thanks sir Jeff.

is this amp is good for 500watts 8ohms speaker? like p audio c12 500mb?

[Jef2]

Thanks sir Jeff.

is this amp is good for 500watts 8ohms speaker? like p audio c12 500mb?

based on the amplifier specs,  it will work.  but i still doubt the grf's ability to power the c12 500 (with less distortion) since the c12 500 has a 4inch voice coil.  i think kung 1 per side lang, ok na.  try the c12 300 instead since this has only 300watts rms.

hope this helps 

[lowriderthug]

based on the amplifier specs,  it will work.  but i still doubt the grf's ability to power the c12 500 (with less distortion) since the c12 500 has a 4inch voice coil.  i think kung 1 per side lang, ok na.  try the c12 300 instead since this has only 300watts rms.

hope this helps  

salamat sir.

OT: tanong lang mga sir, anong gamit na house sa 19east?

[Bellissima]

+1 ako dito....I've tested this amp and it never let me down. Malakas talaga hindi pa lng sya masyado sikat sa market

ACM-M21200 Professional Power Amplifier

SPECIFICATION:

Rated power bridge mode 8 Ohms    3600Watts @ 1 kHz at <0.5% T.H.D.
Rated power (2 X4 Ohms):    1800 Watts per channel @ 1 kHz at <0.5%
T.H.D. both channels driven
Rated power (2 X 8 Ohms):    1200 Watts per channel @ 1 kHz at <0.5%
T.H.D.both channels driven
Power bandwidth:    20 Hz - 20kHz; +0, -0.5 dB at rated 500 Watts 8 Ohm power
T.H.D.(2 X 4 Ohms):    <0.05%@900 Watts per channel from 20 HZ to 20 kHz
T.H.D.(2 X 8 Ohms):    <0.05%@600Watts per channel from 20 HZ to 20 kHz
Minimum load impedance:    2 Ohms
Maximum RMS voltage swing:    110Volts
Frequency response:    10 Hz - 50 kHz; +0, -3 dB at 1 Watt
Input CMRR:    >-65 dB @ 1 kHz
Rated power (1 X 4 Ohms):    1980 Watts @ 1 kHz at <0.5% T.H.D.
Rated power (1 X 8 Ohms):    1300 Watts @ 1 kHz at <0.5% T.H.D.
Phase response:    +20 to -25 from 20 Hz to 20 kHz
Input impedance:    20 k Ohms, balanced; 10k Ohms, unbalanced
Cooling:    Tow temperature dependant variable speed 120mm high output DC fans
Controls:    Two front panel attenuators, rear panel mode switch and gain select switch
Voltage gain:    0.775V, 32 dB or 26 dB
Crosstalk:    >-60 dB @ 1 kHz at rated power @ 8 Ohms
Hum and noise:    >-104 dB, "A" weighted referenced to rated power @ 8 Ohms
Slew rate:    >25V/us
Damping factor (8 Ohms):    >800:1 @ 20Hz - 1 kHz
Indicator LEDs:    2 Clip,2 signal presence, 2 active status, 2Protection
Protection:    Thermal, DC, turn-on bursts, incorrect loads
Connectors:    XLR, Speakon and Binding Post speaker output,
240/230 Volt 20 amp IEC mains
Construction:    16 ga. Steel
Dimensions:    132mm x 483 mm x 498 mm
Net weight:    36kg
Gross weight:    39kg

[/b][/b][/b]

[mixx]

try mo bro 2x na rmx 1850 naka bridge, been using that for quite sometime ok nman sya sa 4ohms na subs(dual 18" 1200wrms)
mas mura pa yung 2x na rmx1850 compared to a single rmx5050, mas flexible pa yung setup mo, and naka qsc ka pa

heres a pic of my amp rack

[maestro_dese_8]

The Peavey PV3800 will do.  Can power my old Fane Colossus 18" for a mid-size gig. 2 per side.




Fane Colossus

I'll be trying this amp on the P Audio C-18elf very very soon. Update ko kayo

sir magkanu yung fane na speaker saka ilang watts ayos ba tumunog yan

[stoney73]

sir magkanu yung fane na speaker saka ilang watts ayos ba tumunog yan

Bro, matagal na yung fane 18inch ko.  I bought them before (on sale) Php 10000 each at JB.  They sounded ok except when the coil gets busted, there are no parts available. 

Check this out http://talk.philmusic.com/board/index.php/topic,163602.25.html

[compact audio]

hi pwede bang magtanong? yong about sa tasso I 12 series okey rin ba? 1500W daw sa 8oms stereo ng rated power nya?

[tjlimjoco]

hi pwede bang magtanong? yong about sa tasso I 12 series okey rin ba? 1500W daw sa 8oms stereo ng rated power nya?

Sir,  try this: http://talk.philmusic.com/board/index.php/topic,175175.0.html

[maestro_dese_8]

Bro, matagal na yung fane 18inch ko.  I bought them before (on sale) Php 10000 each at JB.  They sounded ok except when the coil gets busted, there are no parts available. 

Check this out http://talk.philmusic.com/board/index.php/topic,163602.25.html

thanks bro naka kita kasi ako ng dealer sa dubai its 440 dirhams about 5k sa peso tapos emminence kappa pro 15 4k lang sa peso each.. looks interesting ano po sa palagay nyo

[stoney73]

thanks bro naka kita kasi ako ng dealer sa dubai its 440 dirhams about 5k sa peso tapos emminence kappa pro 15 4k lang sa peso each.. looks interesting ano po sa palagay nyo

Bro, ok ang fane at 5k worth.  But side by side comparison, outperformed ito ng p.audio c-18elf ko ngayon  



Remember, The wrong piece of gear, at the right price, is still the wrong piece of gear.  

[maestro_dese_8]

oo nga noh. salamat sa payo. go p.audio..... invest the right gear!!!!!!

[AE_Audio02]

Nakabili ako last week ng sub woofer speaker Crown S-PRO-152 ang napili ko (limited budget kasi hehehe..)
http://crown.com.ph/index.php/product/search/subwoofer#passivesubwoofer

Nakasulat sa box nya power rating is 500W to 1000W at 8 ohms.

Ano kaya yun affordable amp na pwede dito?
yun sanang Crown LPS-2500 kaso bitin ata sa power rating.

Ang max budget ko eh P20k lang.

Any suggestion?

Thanks in advance.

[lowriderthug]

try mo bro 2x na rmx 1850 naka bridge, been using that for quite sometime ok nman sya sa 4ohms na subs(dual 18" 1200wrms)
mas mura pa yung 2x na rmx1850 compared to a single rmx5050, mas flexible pa yung setup mo, and naka qsc ka pa

heres a pic of my amp rack

saan mo gamit ung SoundStandard na amp na nasa pinaka ilalim?

[stoney73]

try mo bro 2x na rmx 1850 naka bridge, been using that for quite sometime ok nman sya sa 4ohms na subs(dual 18" 1200wrms)
mas mura pa yung 2x na rmx1850 compared to a single rmx5050, mas flexible pa yung setup mo, and naka qsc ka pa

heres a pic of my amp rack

This is a good way of setting-up.  At 4 ohms bridged,  the QSC RMX1850 can fire 1800 watts.  Enough to supply the 1200 watts for the dual 18".    The best part,  you're geared up with QSC amps on your rack.

[ryanbairan]

we used this amp crown power base 2, sa sub

[karlwilson]

try mo bro 2x na rmx 1850 naka bridge, been using that for quite sometime ok nman sya sa 4ohms na subs(dual 18" 1200wrms)
mas mura pa yung 2x na rmx1850 compared to a single rmx5050, mas flexible pa yung setup mo, and naka qsc ka pa

heres a pic of my amp rack

pano ba mag-bridge ng amp sir?