help on SONAR X2 Producer, NO SOUND on Playback

[alexssiea27]

mga sir...

pano po ba dapat ang settings ng SONAR X2 Producer.. di ko magamit kasi wala xang tunog pag playback na...

di tuloy ako makapag edit...

thanks po!!!

[skin]

Have you chosen your audio device under Edit - Preferences?

[jowash]

mga sir...

pano po ba dapat ang settings ng SONAR X2 Producer.. di ko magamit kasi wala xang tunog pag playback na...

di tuloy ako makapag edit...

thanks po!!!

1.Open Sonar
2. Press P keyboard shortcut for preferences
3.under AUDIO select playback and recording
4.select ur driver mode (kng wala kang external audio interface select MME 32bit)
5.under Audio select DRIVER SETTINGS  make sure na may playback and record timing device selected click wave profiler
6.click apply and ok

[alexssiea27]

1.Open Sonar
2. Press P keyboard shortcut for preferences
3.under AUDIO select playback and recording
4.select ur driver mode (kng wala kang external audio interface select MME 32bit)
5.under Audio select DRIVER SETTINGS  make sure na may playback and record timing device selected click wave profiler
6.click apply and ok

sir... ginawa ko na po ito pero wala parin playback....

pag binubuksan ko yung sonar x2
e2 po lagi lumalabas...
di ko po kasi maintindihan eh...

http://i1060.photobucket.com/albums/t454/alexssiea27/v845sa.jpg

[alexssiea27]

1.Open Sonar
2. Press P keyboard shortcut for preferences
3.under AUDIO select playback and recording
4.select ur driver mode (kng wala kang external audio interface select MME 32bit)
5.under Audio select DRIVER SETTINGS  make sure na may playback and record timing device selected click wave profiler
6.click apply and ok

[jowash]

check lng kng may ibang apps na gnagmit yung audio card mo na open like vanbasco,skype,yahoo messenger etc.
kng wala sa audio under  driver settings check mo sampling rate ng project kng supported ng audio card mo
or try mo yung ibang driver mode under playback and recording like WDM/KS

bawat palit mo ng driver mode
run mo lng ang wave profiler
pra mkita mo ang supported sample rate ng audio card mo sa selected driver mode


or install ASIO4ALL tpos select mo sa driver mode asio google lng

[skin]

Asio4all ka na lang.

[coy_2cute]

kaya talagang recommended na gumamit ng separate Audio Interface...

[KitC]

Ugh! VIA onboard. Should try to obtain a proper audio interface if you want less headaches. Most onboard audio default to 48 kHz and their drivers aren't that sophisticated enough to perform adequate sample rate conversion,  plus they can't output anything if the software is set otherwise. See if that chipset has a control panel where you can change sample rates, and always make sure both the chipset and Sonar are set to the same rate. One caveat about using onboard audio drivers is that they usually aren't flexible in the buffer/latency setting department, which is crucial if you want low latency operation.

Asio4all can work but I prefer to have less drivers along the chain - the less variables, the easier it is to troubleshoot. You can add asio4all eventually on when you want asio compatibility - better if you are comfortable mucking around with drivers and buffers later on.

[jowash]

Yes Sir recommended talaga ang audio interface kng wala ASIO4ALL mna buy later

 some built in audio cards have high AD/DA CONVERTERS
in my case mas mataas pa nga conversion rate capability kesa sa sa audio interface ko
 sa built in magagamit pero dpende talaga sa  set up  at specs ng gamit


u can check ur built in sound card capability as long na d ka lalagpas sa mkakaya ng card
sa properties mo SOnar X2 will switch it for u automaticaly